- #Tool studio emmc download s3 install
- #Tool studio emmc download s3 update
- #Tool studio emmc download s3 Pc
- #Tool studio emmc download s3 zip
If you already installed a previous version of Windows CE you can jump to the "Flashing or updating bootloader" section. Recovery mode is needed only if your module is currently booting Linux or not booting at all.
#Tool studio emmc download s3 update
If you already updated your bootloader and image using the update tool you don't need to use recovery mode or perform an update from the bootloader, so you can skip the next chapters. Make sure there is no SD card inserted in the carrier board in order to enter recovery mode properly
If you are updating to version 1.1beta4 please consider that you need to clear registry or to change those registry entries to be able to access flashdisk and sd card If you are using default display configuration you can just clean the registry to keep default behaviour. This means that you should change its value from 0 to 1 or viceversa to keep the display working if you rely on this signal. If you are updating to version 1.1beta2 please consider that the "output enabling polarity" (oep) parameter of the display configuration has been changed to match the behaviour it has on our other modules.
We also sometime experiences some issues with USB devices when the system is rebooted using the coldboot option of update tool, an hardware reset is recommended to avoid those problems. If you are running 1.0beta6 there is an issue with the update tool version that is included in the image, so you should run the updatetool version included in the 1.0 image download (there are two executables, updatetool_ce7.exe for Windows Embedded Compact 7 and updatetool_ce8 for Windows Embedded Compact 2013). If a bootloader is provided in the download package you must update both the image and the bootloader (this require two separate operations in the update tool) before rebooting your device. If you are already running at least the 1.0beta6 image you may use update tool to update the existing image.
#Tool studio emmc download s3 Pc
Remove and re-insert the SD card, your PC will ask you to format itįormat the card and copy eboot.imx, nk7.nbx and nk8.nbx to the card (check that those files are not read-only) Select “write" and wait until the write process is completed Select the drive letter matching your SD card reader in the “Device" box (be careful, the devices are not filtered and you may overwrite a regular hard drive by mistake!) If you plan to use rev.1.2 and the new SPL bootloader you'll have to select eboot-colibri.img or eboot-apalis.img, depending on the module format you are using.
#Tool studio emmc download s3 zip
Launch it and select the eboot.imx file contained in the zip you downloaded. The image can be written using the Win32 Disk Imager tool. Windows Embedded Compact image for the iMX6 modules (including Windows Embedded Compact 7 and Windows Embedded Compact 2013) can be downloaded here. Make sure to update both the image and the bootloader without a reboot inbetween. To update to image V1.3b4 using the Update Tool you'll need to use the update tool V7.6.0 or newer, because the format of compressed images has been changed. This is a know issue (#31253) and there are two applicable workarounds. The WinCe image V1.3b2 image may take more than five minutes for the first boot, and it will not mount the \FlashDisk folder. All other information in this article is not relevant for you. Only WinCe release V1.2b2 and newer are supported by the Easy Installer.įor using the Easy Installer, make sure you activate the boot partition.
#Tool studio emmc download s3 install
Using the Toradex Easy Installer is the recommended way to install Windows Embedded Compact images onto any Colibri iMX6 or Apalis iMX6 module. The image has been tested using the Apalis and Colibri Evaluation Boards, those are the suggested platforms for experimenting with the image. The image runs on all Apalis and Colibri iMX6 modules. Is this page helpful? iMX6 WinCE Bring-up Disclaimer